elongations

英 [ˌiːlɒŋˈgeɪʃənz]

美 [ˌilɔŋˈgeɪʃənz]

n.  拔节; 拉长；伸长度；延伸率; 伸长（延伸）率
elongation的复数

双语例句

• Most of the specimens show distinct elongations of components.
  多数标本的组份呈显著的拉长现象。
• These fibers are characterized by having high strengths, high elongations and good to excellent elastic recovery.
  这些纤维的特点是具有高强力，高伸度和优异的弹性恢复。
• The compliance of brachial artery at different elongations ( from 100%~ 140% of natural length) invitro was calculated on the basis of measurement of pressure-volume relationship in brachial artery of young men who died from accident.
  通过对人的离体肱动脉全压力范围内压力（P）&容积（V）关系的测定，计算了血管自原位长（100%）及拉伸至140%间各阶段之顺应性（C）。
• Changes of Compliance and Morphology of Human Brachial Artery at Different Elongations and Their Clinical Significance
  不同拉伸状态下人肱动脉顺应性与形态学的变化及其临床意义
• Finally, the statistic analysis of 290 measured elongations is constructed, which confirms the necessity of several modified items in the calculation method of elongation for small curvature tendons.
  最后，对索塔锚固区共290束环向预应力筋实测张拉伸长值结果进行了概率统计分析，证实了理论伸长值修正算法中各项修正的必要性。
• It is found that the electric field improves elongations in 1420 alloy markedly, but has little effect on strengths.
  研究表明：电场时效可在一定程度上提高1420合金的延伸率，但对强度则基本没有影响；同时，电场时效减少沿晶分层断裂比例，增加穿晶断裂及微区塑性变形。
• Mechanical properties analyses showed that, compared to unreinforced pure Ti, the hardness, tensile strength and modulus were greatly improved, whereas their elongations were reduced.
  力学分析结果表明，同未增强的纯钛基体相比，复合材料的硬度、抗拉强度有了很大的提高，但延伸率大幅下降。
• Space Charge in EPR Insulator in Different Elongations Experiment Analysis for Tension and Destruction of Fiber Reinforced Rubber Composites
  不同拉伸率的乙丙橡胶中空间电荷分布的研究纤维增强橡胶复合材料拉伸与破坏的试验分析
• The results show that as the increase of the TDDM content, Izod impact strength first increase and then decrease, while the tensile strength and elongations of blends slightly decrease with the amount of TDDM.
  结果表明：随TDDM含量的增加，共混物的冲击性能呈先增大后减小趋势。而拉伸强度，断裂伸长率降低。
• The yield strength ratio of hot dip galvanized dual phase steels will increase with increasing of leveling elongations. When the leveling elongation of steel is over 1.0%, its yield strength ratio is beyond the standard 0.61 requirement.
  随平整伸长率增加，热镀锌双相钢屈强比增加，当平整伸长率大于1.0%时，钢的屈强比超过标准0.61的要求。